Advanced firmware to add native Apple HomeKit and custom configurations, compatible with any SoC based on ESP32, ESP32-S, ESP32-C and ESP8266 series. (Shelly, Sonoff, Electrodragon, Tuya...)
OTHER License
Bot releases are hidden (Show)
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.8.0:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.8.0:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.8.0:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
Changelog v3.7.0:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
"t":50
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Changelog:
"ic"
key in configuration section. It contains an array of I2C buses."c":
SCL GPIO."d":
SDA GPIO."q":
Bus frequency in KiloHertz.First declared bus will be bus 0, and second will be bus 1.
"mc"
key. It is an array that contains all connected MCP23017 interfaces. You can connect up to 16 MCP interfaces (8 per I2C bus), having up to 256 extra GPIOs for outputs."b":
I2C Bus."a":
Address. First MCP23017 begins at 32."ca":
from 0 to 255. Initial state of all channel A GPIOs."cb":
from 0 to 255. Initial state of all channel B GPIOs."ca"
and "cb"
values are the result of convert 8 bits binary string to decimal. For example, to set all channel A GPIOs to LOW, but second GPIO to HIGH, you must use 00000010
in decimal: "ca":2
.Use of MCP23017 with actions:
To call a GPIO from a MCP23017 interface, you must use normal "g":
key of "r":
array. ESP8266 GPIOs are from 0 to 16, but MCP23017 GPIOs are used in this format: "g":XYY
For example, to set to HIGH GPIO 4 of third declared MCP interface:
"r":[{"g":304,"v":1}]
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Published by RavenSystem almost 4 years ago
Published by RavenSystem almost 4 years ago
Changelog:
Read Wiki for more info.
Published by RavenSystem almost 4 years ago
Published by RavenSystem almost 4 years ago
Published by RavenSystem almost 4 years ago
Published by RavenSystem about 4 years ago
Changelog:
value - 2
.Read Wiki for more info.
Published by RavenSystem about 4 years ago
Changelog:
Read Wiki for more info.
Published by RavenSystem about 4 years ago
Published by RavenSystem about 4 years ago
Changelog:
Read Wiki for more info.